Hydrofoamer 481 96 ounce Container HydroFoamer
Hose End hydrofoamer 481 - sprayer with consistent
dilutions of your choice
The Hydrofoamer 481 can
be turned on or off using the trigger on the spray gun and to
clean the device, the concentrate container is easily
disconnected via a fast quick coupler. The hydrofoamer 481 is
non-electric and no installation
is required,
making it extremely user-friendly – just fill the concentrate
container and connect the hydrofoamer 481 to a water source.
HydroFoamer 481 hose
end proportioners combine automatic dilution with convenient
control of where and how solution is applied. Hydrofoamer 481s
provide a thick, rich foam for more "cling" time on the surface
being cleaned.
On and off functions
are controlled using a trigger on the spray gun. To rinse, the
concentrate container is disconnected via a quick coupler.
|
The hydrofoamer 481
is most suitable for the following applications:
|
|
Discounts for 5
or more hydrofoamer 481 click the button for current
pricing.
Operation:
1. Unscrew
hydrofoamer 481 lid assembly from container.
2. Select
a metering tip using the chart below as a guideline and press
the tip firmly into the hose barb on the bottom of the lid
assembly. Install the suction tube on the hose barb.
3. Fill
the 96 ounce container with concentrate. Screw hydrofoamer 481
lid assembly securely onto container.
CAUTION:
Hydrofoamer 481 lid assembly must be securely fastened to
container to prevent accidental spilling of concentrate during
use of foamer.
4. Insert
hydrofoamer 481 lid assembly into female quick connect on spray
nozzle.
5. Connect
a garden hose with 3/4" male garden hose thread to the base of
the spray nozzle handle. Turn on the water supply to the hose.
(Minimum 25 PSI water pressure is required to operate the
hydrofoamer 481.)
6. Grasp
the spray nozzle handle in one hand and the hydrofoamer 481
container in the other. Squeeze the spray nozzle handle to begin
foaming. Continuous operation can be achieved by using the
handle lock provided on the spray nozzle.
Rinse by disconnecting the spray nozzle from the foaming lid
assembly. To remove the foamer from the spray nozzle, simply
grasp the quick connect on the spray nozzle in one hand and the
foamer assembly in the other.
Pull in opposite directions. (The outside collar around the
quick connect will slide toward the spray nozzle, disengaging
the foamer barrel.)
Metering
Tip Selection:
Dilution
ratios below were achieved at 40 PSI, cold water and water-thin
viscosity (1.0 CP). Ratios will vary given PSI, water and
ambient temperature, water flow rate, and product viscosity. At
water-thin viscosity,
the
efficiency of the eductor is at its maximum with the black or
gray tip. Removal of the foot strainer on the concentrate
pick-up tube will also change these ratios.
If no tip is listed,
the dilution ratio delivered falls between those shown.
Parts For Hydrofoamer 481 Below
|
HydroFoamer
481 or 483 Lid for
96 ounce
HydroFoamer 481 or 48 ounce Hydrofoamer 483.
Click button
for current price
|
Quick Coupler
for HydroFoamer 481 or 483
or HydroSprayer
381 or 383. Couples Lids to Spray Guns.
Click button
for current price
|
HydroFoamer
481 or 483 or HydroSprayer 381 or 383
Spray Gun
without Quick coupler. Insulated grip Spray Gun.
Click button
for current price
|
HydroFoamer
481 or 483 or HydroSprayer 381 or 383
Spray Gun with
Quick coupler.
Insulated grip
Spray Gun and coupler.
Click button
for current price
Suction
tube for hydrofoamer 481 or 483 or
Hydrosprayer
381 or 383, goes to the bottom of 48 ounce bottles or
96 ounce bottles. Comes With Chemical strainer
on bottom of tube.
Click button
for current price
|
96 Ounce
Bottle for HydroFoamer 481
or HydroSprayer
381
Click button
for current price
|
Metering
tips for chemical dilution. Use with
hydrofoamer 481 or 483
or
hydrosprayers 381 or 383.
Click button
for current price
|